Whoop Whoop!! I so excited because I get to check off a huge project in my office makeover to do list. Here we are in Week 4 of the One Room Challenge and I finally got our DIY L Shaped Desk installed. I can’t tell you what a relief it is to finally have it finished. It’s only one item from my to do list but it was the largest of them all. And I owe so much thanks to my awesome husband for all his help and support; although he said he doesn’t want any credit so please don’t tell him 😉
We installed our L shaped desk as a built-in of sorts by using and building around some Pottery Barn desk components I scored in a FB buy/sell group for $0. Yep they were F-R-E-E as in zip, zilch, nothing. I love free stuff and I’ll tell you how I pulled that off in a bit. But first let me show you how we did it.
The measurements of our desk is 81″ from each corner. Your desk might need different dimensions.
This post contains links to products, if you purchase something after clicking on my link I may earn
a small commission (at no extra cost to you).
In addition to affiliate links a portion of this project has been sponsored by Wagner. I met them last year at a blogging conference and I loved their demonstration. They agreed to provide me with a large Studio Spray Tent and a Studio Home Decor Sprayer in exchange for writing a post. I was happy to use their products to paint the desk parts. My thanks to them as well!
DIY L Shaped Desk Supply List
- Two (2) Desk Components or wooden 2-Drawer File Cabinets
- One (1) Sheet 3/4″ thick Premium 4′ x 8′ Ripped into two 24″ wide sections
- (premium has a one side that’s paint/stain quality)
- 15′ of 1″ x 4″ Pine
- Two Heavy Duty Shelf Brackets – 19″-20″ that will support at least 200 lbs.
- Eight (8) Corner Brackets (two holes on each side)
- 5/8″ wood screws (for corner braces)
- Four (4) 3/4″ Wood Screws
- 2.5″ Wood Screws
- Four (4) 6″ Flat Brace Brackets
- Cordless Drill
- Stud Finder
- 4′ Level
- Miter Saw
- Skill Saw
- Kreg Rip Cut Circular Saw Guide
- Zinsser 1-2-3 Primer
- Acrylic Paint (I use this for durability)
- Paint Sprayer
- Spray Shelter
- Paint Brushes
- Saw Horses
- Spray Paint
- Sand Paper (150 Grit)
- Sanding Sponge (80 and 150 Grit)
- Edge Veneer Tape 3/4″ x 25′
- Bandit Edge Trimmer
- Box Cutter
DIY L Shaped Desk Preparation
- Purchase a 4′ x 8′ sheet of 3/4″ plywood and ask the hardware store to rip it for you if you don’t have a table saw. The blades on these aren’t changed often so determine if you’re willing to risk it. We did and there was a tiny bit of splintering that luckily was on the underside.
- When you get the half sheets home use the Kreg Circular Saw Guide to cut one 81″ long and the other at 57″ long.
- Sand down the edges that will be your front and sides and ease the edges of the outside corners with sandpaper.
- Use the iron to apply the edge banding to the edges of the plywood. Align the top edge just slightly higher than edge of the plywood.
- When applying the edging around the eased corner work slowly to ease the wood around the corner so that it doesn’t crack.
- Use the Edge Trimmer to trim off any high edges, then sand the edges so all around to take off any sharp feeling.
Painting L Shaped Desk Parts
- If your components aren’t new, remove the hardware, drawers, and shelves from your desk components.
- Give everything a light sand with 150 Grit paper to rough out any dings and to give the finish some tooth for the paint to adhere.
I promised I’d tell you how I got these Pottery Barn desk components and here goes. Someone had posted two of them on a buy sell group and they wanted $125 for both. That was way more than I wanted to pay so I set Facebook to send me notifications about that post. About a week later I get a notification and the lady said “free if you can pick up today.” I jumped on it.
Within 15 minutes they were in the back of my husband’s brand new truck (shhh don’t tell him I hauled something in his new truck before he did). My patience paid off in a big way.
- Set up the Spray Shelter and thin the Primer according to the instructions on the can and for the Home Decor Sprayer. Zinsser is pretty thick so I had to thin it at about 1/3 water to 2/3 primer.
- Set your parts on 2x4s to get them off the bottom of the spray shelter.
- Use a sweeping motion with your paint sprayer like you would with spray paint. Follow the directions on the Studio Home Decor Sprayer to test your paint flow volume for the best finish.
It’s almost always windy at our house and since the long piece of the desk was too big to put in the spray shelter and move around it I painted the two top pieces of the L Shaped Desk by hand with a brush. Floetrol is your friend when hand painting such a large area. And here’s a little tip to get the best finish…after you get all the paint on lightly mist the top with a spray bottle to cover the entire area and then do one last swipe with your brush. It will look like glass and when it’s dry the surface will be perfect.
While everything is drying paint the hardware.
- Use the 120 grit sanding sponge to lightly scuff the surface.
- Use random screws and attach them to a board temporarily.
- Holding it upside down spray paint in light coats all the nooks and crannies.
- Set on a board upside down until fully dry.
- When fully dry re-attach the handles to the desk drawers and re-install the drawers in the desk.
Installing your DIY L Shaped Desk
Yay, installation day is finally here!!! It seemed like it took forever but I worked at it a little here and there and we finished installing it 3 weeks after I started the One Room Challenge, but really it was nine days from the time I started painting until we installed because I worked it around my part time job.
Here’s the steps we took to install our DIY L shaped desk to the walls.
- Set your desk components or filing cabinets on either wall 79.5″ from the corner and adjust them so the front and sides will have a 1″ to 1.5″ overhang and use a square on the floor to ensure they are square to the wall. My desk components are only 18″ deep so I have a gap at the wall .
- Use Painters’ tape to mark the corner of your desk. This will make it easier to get it back where it belong in the final steps.
- Span a straight 2×4 over the two sides and use a level to determine if your floors are level. If so great, move on to the next step. If not determine which side is highest. This will be the side from where you start.
In our room the left side from the corner is higher than the right. This was our starting point.
- From each corner use the Stud Finder to locate and mark the center of each stud.
- Cut two 1″ x 4″ boards, one 79″ long and the other 78-1/4″ long.
- Mark a line on the wall even with the top of your desk component on the highest side of the room.
- Line up the end of one of the 1×4’s to the line on the wall and the other end in the corner using the level.
- Using the 2.5″ wood screws and cordless drill to fix the 1×4 to the studs. Alternatively you could use a nail gun to attach the 1×4 bracings to the wall but I wanted the option of removing it without destroying the wall.
- One screw per stud is enough. However, if you can’t place a screw into the stud at the very end of the board double up the screws on the last stud.
- Using the first 1×4 as a guide now install the second one on the other wall using the level to keep it, well, level 🙂
- With the 1×4 braces installed on the wall connect the eight Corner Brace to the 1×4 so that the top is flush with the 1×4. (see pic below)
- On the second stud from each corner (approx 32″ in from the corner) install a 9.5″ piece of 1×4 below the horizontal piece. This is where you’ll install the Heavy Duty Shelf Brackets which will help support the expanse of the desk. (see below)
- Pre-drill holes in each corner through the top of your desk components. Drill from the underside and protect your paint job with painters’ tape. We’ll address these holes last.
With all the corner bracings and the two heavy duty brackets installed it’s time to install the top of your desk. The 81″ board for our L Shaped desk is under the window with the shorter section on the left.
- Set the 81″ piece over the desk component and into the corner. Now, most houses aren’t perfect so be prepared to see gaps along the walls.
- Set the 57″ piece on the other side and square it up to the longer section. Again you’ll have to do some adjusting to get the square. I have about a 1/2″ gap in one section along the wall where my two boards meet. I’ll be filling that in with silicon caulking and may even cover it with some sort of trim #oldwonkywalls. Don’t lose sleep if it’s not perfect #recoveringperfectionist
- After you get the two sides set and the sections that meet are all squared up you can now use the 5/8″ screws to attach the underside of the L Shaped Desk top to the corner braces. Using the 3/4″ screws attach the underside of the desk to the heavy duty brackets. You might want to verify on a scrap of plywood that the screws your using with the corner brackets and the heavy duty bracket won’t pierce through your top. Alternatively you could use a nail gun and nail through the top of the Desk into the 1×4 bracings, but I wanted the option of removing it without destroying anything.
Lastly we need to connect the short board and long board together.
- Using 5/8″ screws attach the four Flat Brace Brackets across the seam where the two sections of your DIY L Shaped Desk meet.
Now line up the desk components so they are square to the wall and have the overhang you like. If your floors aren’t level then you may need to use some wood shims on the top of one to bring it to level. We had to shim above the right side and below the top of the desk. We were able to measure and buy a piece of trim thick enough (about 1/4″) that we cut to length.
- Attach the desk component or filing cabinet to the L Shaped Desk top with screws long enough but not so long that they pierce the top (because that would suck). Your situation will vary from mine, my screws were 2-1/4″ long since the top of my desk component was so thick.
That’s it, that was your final step 😀 You can dab a little white paint on the wall brace screws if you want. But really once you get all moved into your new desk no one will ever see them.
Here are a few pictures but I’m sorry they are not the greatest so I’ll be reshooting them once the entire room is completed and put back together.
I’ve been very long-winded today so if you’re still with me here’s my updated To Do List. I actually got to cross off three projects this week because I did get my chair recovered and stained and hung the shelves. One of those projects I’ll share next week and the other will have to wait until after the big reveal in two weeks. So really there are only a couple things I really have left, it’s all about the organization and the rug. Ah, how good it feels to be this close to the finish line 😀
Give the room a fresh coat of paint. Build an L-shaped corner desk. Recover my existing desk chair. Take down the unused TV. Updating the lighting.
- Create organization with peg board or some other fun product.
- Replace the existing area rug.
Install shelves over the desk.
Come back next Thursday to check out my next post in my office makeover. And remember to head on over and visit ORC participants’ projects for Week 4 through the link below:
Still tired but happy to be nearing the finish line,